 Specifications of Digital Counters |
| Model |
C-500 |
C-700 |
 Displayed digits |
|
 Selection of 10µm |
|
Selection of 1µm |
| Display |
|
| -9999.99 — 00.00 — 9999.99 |
| -999.999 — 0.000 — 999.999 |
| High-luminance LED display with 7 segments (red) |
|
Power supply voltage
& power consumption |
|
AC100V — AC240V
/ 9VA or lower |
| Operating temperature |
|
0 — +40ºC |
| Compatible Linear Gauges |
|
Selection of 10µm display |
|
Selection of 1µm display |
|
| DL-2, D-5, D-10, D-20, D-30, D-50, D-100, DN-10, DN-20, D-5UZ |
| DL-2S, D-5S, D-10S, D-20S, D-30S, D-50S, D-100S DN-10S, DN-20S |
|
| Accessories |
|
| AC power cord (2m) ; One cord |
| Metal fittings for panel installation ; Two units |
|
( to be used for installation in panel and securing stand fittings ) |
| Stand fittings ; One unit |
|
( to be used when counter is used as desktop device ) |
|
Terminal block functions
( Rear panel ) |
|
| Terminal block |
–> Screwless terminal block |
| Usable electric cables |
–> AWG22 – 28 |
| Length of peeled wire of cables |
–> 8 – 9mm |
| Pin alignment |
| (*1) |
St/Sp |
Controls “START” and “STOP” of MAX, MIN, P-P
measurement mode. |
| (*2) |
React |
Controls “SUSPEND” and “START” of P-P
measurement mode. |
| 3 |
Latch |
Controls “LATCH” and “CANCEL” of measured value. |
| 4 |
Reset |
External “RESET”
“PRESET” ( Function available only in Model No. C-700 ) |
| 5 |
Alarm |
Error signal output |
|
Max
Display |
Min
Display |
P-P
Display |
| (*6) |
-NG |
Outputs -NG based on
OK±NG judgment (red LED). |
–> |
+NG(2) |
-NG(1) |
NG(2) |
| (*7) |
OK |
Outputs OK based on
OK±NG judgment (green LED). |
–> |
OK |
OK |
OK |
| (*8) |
+NG |
Outputs +NG based on
OK±NG judgment (orange LED). |
–> |
+NG(1) |
-NG(2) |
NG(1) |
|
(1) : NG output in first stage
(2) : NG output in second stage |
| 9 |
GND |
GND |
| (* ) |
Circled numbers indicate functions available only in Model No. C-700 |
|
Dip sw setting functions
( Printed circuit board ) |
|
| Dip(1) |
|
Dip(2) |
| SW 1 |
Select 1µm or 10µm |
|
SW 1 |
Settings by Manufacturer |
| SW 2 |
Select direction of
counting. |
|
SW 2 |
Select whether or not to include
default values for OK±NG judgment. |
| SW 3 |
Select activation or non-
activation of error output. |
|
SW 3 |
Select either “orthogonal” or “sine”
for input waveform. |
| SW 4 |
Select activation or non-
activation of overflow. |
|
SW 4 |
Select either 400msec or 100msec
for RESET time. |
|
Data output (RS-232C)
D-Sub9P plug
INCH screw |
|
| Options |
|
Excel input software |
|
BCD output board |
|
| Pin Alignment |
| 1 |
NC |
— |
|
Communication mode ; Half-duplexasynchronouscommunication |
| 2 |
Rxd |
in <– |
|
Communication speed ; 9600bps |
| 3 |
Txd |
–> out |
|
Format ; 7Bit ASCI I |
| 4 |
NC |
— |
|
Parity ; even number |
| 5 |
SG |
— |
|
Stop bit ; 1Bit |
| 6 |
NC |
— |
|
RTS / CTS ; Returned when not in use. |
| 7 |
RTS |
–> out |
|
Reception command ; Transmission request ASCI I [T] [t] |
| 8 |
CTS |
in <– |
|
; Reset ASCI I [R] [r] |
|
| 9 |
NC |
— |
|
Connection cables ; Cross cables ( not included ) |
| PK-2002 |
|
; Data imported into Excel cells from RS-232C output. |
| CB-BCD |
|
; Cannot be used in combination with RS-232C output. |
|
| Display functions |
|
| 1/1 display |
–> Displays the measured value as is. |
| 1/2 display |
–> Displays the measured value after halving it. |
| ×2 display |
–> Displays the measured value after doubling it. |
Note ;
With 1µm display and ×2 display, the lowest digit will be displayed as an even number. |
| Presetting display function |
|
| Zero setting only |
|
| Can display preset values |
|
Measurement mode function
[MAX] [MIN] [P-P] |
|
— |
| Current value display |
Maximum
value (Max) |
RESET action is taken by
ST of the ST/SP control
terminal. |
Minimum
value (Min) |
Deflection
(P-P) |
|
OK±NG judgment function
( Refer to terminal output
circuit ) |
|
— |
Current
value mode |
+NG |
OK |
-NG |
Maximum
value mode |
OK |
+NG (1) |
+NG (2) |
Minimum
value mode |
OK |
-NG (1) |
-NG (2) |
Deflection
mode |
OK |
NG (1) |
NG (2) |
|
| Dimensions |
/ |
Weight |
|
| 144(W)×72(H)×160(D)mm |
/ |
950g |
|
